Cart

Stinger CS150B Cap Stapler

Cap Nail Gun For Quick Installation of Synthetic Underlayment

Stinger CS150B Cap Stapler
Free Shipping
IN STOCK

Stinger CS150B Cap Stapler

28 Reviews
Write Review
This is some text inside of a div block.

Speed: 5 cap staples per second (max. cycle rate/second). Tool Weight: 4.2lbs. Fastener Capacity: 200 caps / 200 staples. Cap Type: Full 1" collated plastic caps. Fastener Type: 7/16" crown staples / 18 gauge. Fastener Length: 5/8", 7/8", 1-1/4" and 1-1/2"

Price:
Each
$ 315.75 USD
(as low as
$315.75
Each)
Details

The STINGER CS150B is designed for use with:

5/8" 18ga StaplePac (#0136024)

7/8" 18ga StaplePac (#0136044)

1-1/4" 18ga StaplePac (#0136074)

1-1/2" 18ga StaplePac (#0136094)

Introducing the Stinger CS150B Cap Stapler. The Stinger CS150B Cap Stapler provides builders with proven performance and best practice for securing synthetic underlayment, as well as roofing felt, foamboard, and housewrap. The Stinger CS150B Cap Stapler is light and easy to maneuver, and the ergonomic design helps to reduce arm fatigue. The redesigned clear basket feeds caps in seconds, and the large capacity for caps and staples means fewer stops to reload.

Use Properly

Improper use of the Stinger CS150B Cap Stapler could result in serious injury or even death. Most accidents occur because of the failure to observe basic safety rules and precautions, which are outlined in the “Important Information” section of this manual. This Owner’s Manual should be available to anyone who plans to operate the Stinger CS150B Cap Stapler.

Personal Safety Items

• Do not use tool prior to reading the Owner’s Manual

• Always wear eye protection that conforms to ANSI requirements (Z87.1) and provides protection against flying particles both from the front and side. Eye protection should be worn by the operator and by others in the work area. Eye protection is required to protect against flying fasteners and debris that could possibly cause severe eye injury.

• The employer is responsible to enforce the use of eye protection equipment by the tool operator and all other personnel in the work area.

• To prevent accidental injuries

- Handle the tool with care

- Always assume that the tool contains fasteners

- Always disconnect the air hose from the CS150B when:

• loading staples and/or caps

• performing inspection, maintenance or repair

• clearing a staple or collated cap jam

• the tool is not in use

• leaving the work area

• moving the CS150B to another work location

• handing the CS150B to another person

• storing the tool

- Never point the tool toward yourself or anyone else

- Never engage in horseplay

- Never hold or carry the tool with a finger on the trigger

- Never place a hand or any other part of the body in the fastener discharge area of the tool while the air supply is connected

Air Supply

• Use only clean, regulated compressed air as a power source for this tool. Do not use bottle gases, combustible gases or oxygen as a power source for the tool as the tool may explode.

• Do not use air supply pressures that exceed 110 PSI (7.7 bar). Exceeding the recommended maximum operating air pressure will greatly increase tool wear.

• The air supply must be capable of maintaining the operating air pressure of the tool. Pressure drops in the air supply can reduce tool wear.

• Use a pressure regulator and gauge to allow visual inspection of the air pressure being delivered to the tool.

• Use air hoses that have rated pressures of up to 150% of the maximum pressure that can be generated by the power source. The supply hose should contain fittings that will provide quick disconnecting from the male plug on the tool.

• Use quick connect fittings that allow the tool to be unhooked from the air supply quickly and easily.

• Do not use fittings that will not allow the tool to exhaust when the air supply is connected.

Specifications + Warranty

Operating Pressure 80 - 110 PSI

Weight 4.5 lbs | 1.9kg

Staple Capacity 200 staples (2 - 100 count strips)

Cap Capacity 200 collated plastic caps (1 reel)

Air Inlet 1/4" | 6.35mm

Fasteners: STINGER StaplePac only. Each 2000 count StaplePac consists of 20 strips of 5/8”, 7/8”, 1-1/4”, & 1-1/2” | 16mm, 22mm, 32mm & 38mm, 18 gauge staples (100 staples per strip) and 10 reels of 25mm diameter collated plastic caps (200 caps per reel).

Audio Data: Loudness levels presented in the table below are in accordance with EN 792-13 (EN12549+A1:2008)

LpA 1s,1m = 86,7 dB(A)

LwA 1s = 99,7 dB(A)

LpA 1s, = 90,7 dB(A)

These levels are characteristic of the tool but does not represent the sound that occurs at the point the tool is used. Workstation design can reduce the noise levels, for example by placing the work piece on sound absorbent supports.

This value is in accordance with EN 792-13 (ISO 8662-11:1999)

Equivalent Vibration Value = ahv,eq (m/s2) = 3,3

Vibration Data: This value is characteristic of the tool and does not represent the effect of the hand-arm system when using the tool.

Air Consumption: 0.75 liters at 7 bar operating pressure

MAINTENANCE

1. Disconnect the air hose from the tool when performing inspections, maintenance, or repairs.

2. Use air line lubricators. If lubricators are not available, or if hose length exceeds 3 meters, add 2 drops of non-detergent 20-weight oil daily into the air inlet of the tool.

3. Whenever repairs or replacement of parts inside the body occur, check the piston “O” ring for adequate grease lubrication.

4. Never use any parts other than genuine STINGER replacement parts. To order, call 800-746-5659.

5. Periodically clean the Magazine and Nose of the tool with a mild solvent. STORAGE

1. Disconnect the air hose when storing the tool.

2. Never store the tool in cold weather environments for any duration of time as any frost or ice formation in the tool will cause tool failures.

3. For prolonged storage, add 2 drops of oil to the air inlet of the tool prior to discontinuing use. Also clean the exterior of the tool with a mild solvent.

LIMITED WARRANTY

MODELS COVERED. This limited warranty is provided by National Nail Corporation (“National Nail”) andcovers its STINGER® brand pneumatic tools (Model Nos. CS58, CS150, CS150B, CN100B, and CN100). This warranty is provided to the original purchaser of the tool only; it is not transferable.

WARRANTY COVERAGE. All external components on your STINGER tool (including cap assemblies, cap castings, and housing castings) will remain free from defects in workmanship and materials for 1 year from the date of purchase. All other components will remain free from defects in materials and workmanship for 90 days from the date of purchase. If National Nail determines that a component of your STINGER tool shows a defect in workmanship or materials within one of these covered time periods, National Nail, at its option, will either repair or replace your defective STINGER tool. To be eligible for this coverage, the tool must have been manufactured within the last year and you will need to show proof of the date of purchase.

NOTE THAT ANY REPAIRED OR REPLACED PRODUCT WILL BE WARRANTED ONLY FOR THE UNEXPIRED

TERM OF THE ORIGINAL WARRANTY.

ITEMS NOT COVERED. This limited warranty does not cover the following circumstances:

1. Malfunctions resulting from normal wear or the end of the life of a normal wearing component, such as your tool’s driver blades, bumpers, o-rings, pistons, or piston rings.

2. Abused, neglected or poorly maintained tools.

3. Components, parts, or accessories not proper or fit for use with your STINGER tool, including the use of inappropriate fasteners with your tool.

4. Routine maintenance for your tool.

5. Damage caused by accident, act of God, or misapplication of the tool.

6. Modifications or repairs made to your tool by anyone other than National Nail.

FOR OPTIMAL PERFORMANCE AND TO AVOID THE RISK OF FALLING INTO SOME OF THE ABOVE

EXCEPTIONS TO THIS WARRANTY, it is strongly recommended that you use genuine STINGER parts and fasteners with your tool and have National Nail or one of its local authorized service centers complete any repairs to your tool.

This warranty is in place of all other warranties. National Nail disclaims all other warranties, express or implied, and limits the application of any implied warranties, including the implied warranty for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, to a period of 1 year from the date of purchase. National Nail’s sole obligation and your exclusive remedies are set forth in this warranty. National Nail will not be liable for any incidental or consequential damages.

Some states do not allow the exclusion or limitation of damages, or limitations on how long an implied warranty lasts, so the above limitations may not apply to you.

WARRANTY CLAIMS PROCESS. To obtain warranty service, please call National Nail at 1 (800) 746-5659.

You will be provided with the address to mail returns or, if appropriate, for any local authorized service center where your tool may be evaluated for coverage under this warranty. YOU WILL BE RESPONSIBLE FOR MAILING YOUR COMPLETE STINGER™ TOOL BACK TO NATIONAL NAIL, POSTAGE PREPAID AND INSURED, OR DELIVERING IT TO ANY LOCAL AUTHORIZED SERVICE CENTER. EXCEPT FOR SUCH MAILING AND DELIVERY COSTS, YOU WILL NOT BE RESPONSIBLE FOR ANY COSTS ASSOCIATED WITH ANY REPAIRS COVERED UNDER THIS WARRANTY

Who are the Webflow founders?

What’s a Rich Text element?

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

Static and dynamic content editing

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

How to customize formatting for each rich text

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

Product

Product

No items found.
No items found.
No items found.
No items found.

Related Items..

Related Items..

Name
Information

What’s a Rich Text element?

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

Static and dynamic content editing

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

How to customize formatting for each rich text

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

The Roof Store Logo with white round background
Free Shipping
Nationwide
Only $25
Buy in bulk