Cart

Owens Corning Ventsure 4 Foot Strip Heat & Moisture Ridge Vent

Plastic Ridge Vent by Owens Corning with 20 square inches of NFA offered in limited Texas markets.

Owens Corning Ventsure 4 Foot Strip Heat & Moisture Ridge Vent
Free Shipping
IN STOCK

Owens Corning Ventsure 4 Foot Strip Heat & Moisture Ridge Vent

28 Reviews
Write Review
This is some text inside of a div block.

Owens Corning VentSure 4 foot Strip Heat and Moisture Vent is a type of ridge vent.

Net Free Area 20 square inches
Price:
Each
$ 15.00 USD
(as low as
$15
Each)
Details

VentSure 4-Foot Strip Ridge Vents are designed for roofs with slopes of 3/12 to 16/12.

Installation Instructions

1. Using a chalk line, mark out 1 inch on both sides of the ridge as a guide for cutting a slot in the top of the ridge. See Fig. 1.

2. Cut slot using a circular saw with the blade set at a depth to cut through the wood sheathing only. See Fig. 2.

NOTE: Start and end the cut 6 inches from the edge of the roof. Remove the sheathing debris from slot.

3. Center the vent over the opening that has been cut in the ridge, ensuring the vent sits flat on the roof. Also ensure that the alignment tabs are facing the opposite direction you will be installing the next piece of ridge vent. See Fig. 3.

4. As you install the vents, ensure each vent is pinned together, then nail in place using the nail holes marked on each vent. See Fig. 4.

5. Using a utility knife, cut the final piece to a length long enough so that it is flush with the edge of the roof. Connect making sure that the built-in end caps are exposed and nail in place. See Fig. 5.

NOTE: In most cases, the final piece will not use the interlocking feature.

6. Nail hip and ridge shingles over the vent using nails long enough to meet the penetration requirements of the local building code and shingle manufacturer or use nails provided with the VentSure ridge vent. For a clean look, extend the hip and ridge shingle to cover the interlocking tabs or trim tabs off using a utility knife. See Fig. 6.

INSTRUCTIONS FOR CUTTING SLOTS

Hip and Gable Roofs

Cut slot 1 inch on both sides of ridge to within 6 inches of each end wall or hip intersection. See Fig. 7.

Chimneys

Cut slots 12 inches from chimney. Run ridge vent from end of roof to butt against chimney. See Fig. 8.

Important Notes

1. On architectural shingles, roofing cement should be used where the roof vent lower edge meets the laminate shingle to prevent wind-driven rain or snow from blowing under the ridge vent.

2. Before applying the vent to architectural shingles on new construction, leave underlayment long at ridge and fold back under vent or caulk between low areas of shingle and flange of vent, making sure you don’t plug holes.

3. See instructions for cutting slot.

4. For structures with different ridge heights, be sure to vent the higher ridge provided there is an opening that connects the two attic spaces. It is also acceptable to vent lower ridges with dormers.

5. For best appearance, run VentSure ridge vent from end to end to give the roof a more attractive appearance.

6. For truss roof framing, cut a 1 inch slot on each side of the ridge starting a minimum of6 inches from the rake edge of the roof.

For conventionally framed roofs with a center ridge board, cut a 1 inch wide slot beyond the ridge board starting a minimum of 6 inches from the rake edge of the roof. Combined width of slots and ridge board should not exceed 3½ inches.

Limited Warranty

LIMITED WARRANTY This product is covered by a Limited Warranty which is

available by calling 1-800-GET-PINK or visiting www.owenscorning.com.

Who are the Webflow founders?

What’s a Rich Text element?

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

Static and dynamic content editing

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

How to customize formatting for each rich text

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

Product

Product

No items found.
No items found.
No items found.

Related Items..

Related Items..

Name
Information

What’s a Rich Text element?

The rich text element allows you to create and format headings, paragraphs, blockquotes, images, and video all in one place instead of having to add and format them individually. Just double-click and easily create content.

Static and dynamic content editing

A rich text element can be used with static or dynamic content. For static content, just drop it into any page and begin editing. For dynamic content, add a rich text field to any collection and then connect a rich text element to that field in the settings panel. Voila!

How to customize formatting for each rich text

Headings, paragraphs, blockquotes, figures, images, and figure captions can all be styled after a class is added to the rich text element using the "When inside of" nested selector system.

The Roof Store Logo with white round background
Free Shipping
Nationwide
Only $25
Buy in bulk