3" and 4" sizes must be purchased with either the 1 1/2" or the 2" orders (to qualify for Free Shipping). The Bullet Boot (manufactured by Bullet Products) flexible pipe boot replaces the existing and toxic lead pipe boot at a great price. The Bullet Boot has a 35 year warranty. Protective mesh varies in colors and may not match color of Bullet Boot. Bullet Boots have Free Shipping only when delivered to a Commercial Address. Residential Delivery costs much more. If you want Free Shipping on your Bullet Boots, have them shipped to a Commercial Address, not exceptions.
35 Year Warranty
The Bullet Boot is a new patented product designed to aesthetically replace the old toxic lead pipe flashing products at a competitive price. These boots are a one-piece flexible rubber TPE pipe flashing. This is a one-piece flexible design that goes on the outside as well as the inside of the pipe. The Bullet Boot has one hundred percent UV protection. Furthermore, the boots make an ideal flashing for all types of shingle, tile, metal, and TPO roofing. Additionally, all our boots come with rodent screen built in the top. This prevents rodents, birds, and other critters from entering the vent. As well, the screen prevents unwanted debris from entering the vent. There is no need to paint since it comes in many colors to match virtually any roof application. Finally, this innovative product adapts to any roof pitch due to its flexible material.
Installation Instructions:
Fitting: Remove interfering shingle nails around the perimeter of the roof opening. Depending on the application, apply a bead of shingle adhesive along the bottom of the flange, and slide the top end of the Bullet Boot up and under the shingle. Allow the bottom vent flange to lie on top of the shingles or cut shingle to fit.
Mounting: Care should be taken in keeping the Bullet Boot properly aligned. Nail in place using 1-1/4” coated or stainless roofing nails spaced 6” to 8” on center, or at least 3 per side, maximum of 1” from the outer edge of the flange, and 1-1/2” from each corner. Roofing cement should be applied to all shingle edges and nail heads to prevent water infiltration. In severe weather coastal hurricane zones, it is recommended to caulk around the entire Bullet Boot perimeter, under the vent flanges, and near the outer edges (7108 Permathane Sealant).
Diameters 1 1/2", 2", 3" have 16 Bullet Boots per box.
Diameter 4" has 8 Bullet Boots per box
Wet Fit Application: Fitting: Remove interfering shingle nails around the perimeter of the roof opening. Depending on the application, apply a bead of shingle adhesive along the bottom of the flange, and slide the top end of the boot up and under the shingle. Allow the bottom vent flange to lie on top of the shingles or cut shingle to fit. Mounting: Care should be taken in keeping the boot properly aligned. Nail in place using 1-1/4” coated or stainless roofing nails spaced 6” to 8”on center, or at least 3 per side, maximum of 1” from the outer edge of the flange, and 1-1/2” from each corner. Roofing cement should be applied to all shingle edges. In severe weather coastal hurricane zones, it is recommended to seal around the entire perimeter, under the vent flanges and near the outer edges with a compatible roofing cement or adhesive. It is suggested the roofing cement or sealant be used to cover exposed zinc plated or galvanized nail heads.
Dry Fit Application: Step Flash Installation method, for use without additional roofing cement.
Florida Building Code Specific Installation Instructions
Florida Building Code fastening pattern shown for #10 Pan clip Screw Fastener with a sufficient length to penetrate roof deck by 3/32”. Pan clip for wood deck installation: DMIPD10100T 1”, DMIPD10150T 1-1/2”,DMIPD10200T 2”. FBC approval # FL 25870.1 .The use of a coated or stainless steel Pan clip fastener in place of a coil roofing nail eliminates the need to seal exposed nail heads.
.png){kind=icon}
